Bead Store
A = Miyuki 11° SEED bead, 54*
B = 4mm crystal, 6*
C = 4mm pearl, 1*
*Bead Counts are per repeat, Repeat is approximately 1”
Nymo D, C-Lon Thread or Fireline (4 or 6 pound), #11 or #12 beading needle
Start by waxing and stretching your thread. Tie in a “stopper” bead, leaving about a 8-10”
1. Pick up 4A. Go with thread through the 1st, 2nd, 3rd and 4th A beads. Stack as shown.
2. Pick up 4A, 2B, 1A. Go with thread down through the 3rd and 4th A beads and the 1st B bead added in this step.
3. Pick up 1B, 3A. Go with thread up through the 1st B bead, step #2 and down through the 1 B added in this step.
4. Pick up 3A, 1B. Go with thread down through the 1 B bead added in step #3 and forward through the 3 A and 1 B beads added in this step.
5. Pick up 1B, 3A. Go with thread forward through the 1 B bead, step #4 and the 1 B bead added in this step.
6. Pick up 3A, 1B. Go with thread through the 1 B bead added in step #5, the 3 A and 1 B beads added this step and up through the 2nd B bead added in step #2.
7. Pick up 3A. Go with thread down through the 1 B bead added in step #6 and forward through the 2nd B bead, step #2, the last A bead added in step #2 and the 3rd A bead (of the 4A) added in step #2.
8. a) Pick up 5A. Go forward through the 2nd A bead added in step #3.
b) Pick up 5A. Go forward through the 2nd A bead added in step #4.
9. Pick up 6A. Go with thread forward through the 2nd A bead added in step #5.
10. a) Pick up 5A. Go with thread through the 2nd A bead added in step # 6.
b) Pick up 5A. Go with thread through the 2nd A bead added in step #7.
11. Pick up 2A. Go with thread down through the 3rd and 4th A beads, step #1, (first time) or the 2 A beads added in step #12 (every time after). Continue with thread left to right through the 1st A bead, up through the last A bead and left to right through the 2nd B bead, step #2.
12. Pick up 1C. Go forward with thread through the 1 B and 3rd A beads added in step #4. Continue with thread through the 1st, 2nd, 3rd and 4th A beads added in step #9.
13. Pick up 2A. Go with thread up through the 3rd and 4th A beads added in step #9 and down through the 1st and 2nd A beads just added in this step.
14. Continue by repeating steps #2 through #13 until the necklace is the length that you would like.
15. To add clasp, pick up 3A, clasp, 3A, go with thread down through 2 A beads in necklace. Continue with thread around through the clasp beads several times for strength. Weave the working thread into the necklace and end. Repeat the clasp directions in the same manner at the other end of necklace after removing the stopper bead.
http://www.SandraDHalpenny.com
Sandra D. Halpenny © 2005 - 2023 All rights reserved
Canadian Intellectual Property Office
This pattern may not be copied or distributed in any way without the express written permission of the author. The purchaser of this pattern may use the finished piece for personal use and for selling at arts and crafts shows, etc. No mass production of this design is permitted without permission from the author.
Peyote Purse #23 Necklace Graph Pattern
No comments:
Post a Comment