The Pattern is Free on this Website.
To Purchase a Downloadable PDF: Click HERE
Beads Used:
A = 11˚ MIYUKI Seed beads
B = 8˚ MIYUKI Seed beads
C = Czech Mates Triangle bead
D = 11˚ MIYUKI DELICA beads
E = MIYUKI Tila beads
Start by waxing and stretching your thread, use Nymo D or C-Lon & a #11 or #12 beading needle. I used Fireline 6lb. crystal. Tie in a "stopper" bead, leaving about an 8" tail and begin at step #1.
2. Pick up 3D, go
with thread right to left through the bottom hole of the C bead and up through
the 3 D beads added in the last step.
|
|
|
3. Pick up
1A, 1E 1A, 1B, 1A, go with thread down through the right side hole of the E
bead just added.
|
4. Pick up 1A, go with thread down through the 3 D
beads, step #2.
|
|
5. a) Pick up 1A,3D, 1A, go with thread
down through the 3 D beads, step #2.
b) Pick up 1A, go with thread down through the right side
hole of the E bead added in step #1.
|
|
6. Pick up 1A, 1B, 1A, follow the
blue dotted line in illustration. First going up and then down with working
thread and coming out with thread down through the right side hole of the E
bead, Step #1.
|
|
7. Pick up 1B, 1E, 1A, go with thread
up through the 3 D beads, Step #5a.
|
|
8. Pick up
1C, 3D, go with thread right to left through the bottom hole of the C bead
just added and up through the 3 D beads, Step #5a. Make sure your C bead is
facing up in the same direction as the previous C bead.
|
|
9. Pick up
1A, 1E, 1B, go with thread down through the right side hole of the E bead in
the previous unit and the A bead, left to right through the 1 A bead, as
shown, up through the 1 A bead and the left side hole of the E bead just
added in this step.
|
|
10. a) Pick
up 1A, 1B, 1A, go with thread down through the right side hole of the E bead,
step #9.
b) Pick up 1A, go with thread down
through the 3 D beads, step #8.
|
|
11. a) Pick
up 1A, 3D, 1A, go with thread down through the 3 D beads, step #8.
b) Pick up 1A, go with thread down
through the right side hole of the E bead, step #7.
|
|
12. Pick up 1A,
1B, 1A, follow the blue dotted line in illustration. First going up and then
down with working thread and coming out with thread down through the right
side hole of the E bead, Step #7.
|
|
13. Continue
bracelet by repeating steps #7 through #12 until the bracelet reaches the
length that you would like.
|
Dimensional Bracelet pattern, Free Tutorial - B0272
http://www.SandraDHalpenny.com
Sandra D. Halpenny 2015 - 2016 All rights reserved
This pattern may not be copied or distributed in any way without the express written permission of the author. The purchaser of this pattern may use the finished piece for personal use and for selling at arts and crafts shows, etc. No mass production of this design is permitted without permission from the author.
Automatic Discounts
|
5 or more patterns 10% off
10 or more patterns 20% off 15 or more patterns 30% off Automatic discounts are on patterns purchased separately and does not include any eBooks or printed books) |
![]() |
|
|