A = Miyuki, 11° SEED bead
B = Miyuki, 11° SEED bead C = 4mm Fire-polished crystals, Bronze Start by waxing and stretching your thread, use Nymo D or C-Lon & a #11 or #12 beading needle. I used Fireline 6lb. crystal. Tie in a "stopper" bead, leaving about an 8" tail and begin at step #1. |
1. Pick up 1A, 1B, 3A, 1B, go
with thread up thorough the 1st A bead just added.
|
2. Pick up 1A, 3B, 1A, go with thread
down through the 1st A and 1st B bead, step #1.
|
3. Pick up 2B, 5A, 2B, go with thread
up through the last B bead and down through the 1st B bead, step #1, and the
first 2 B beads just added in this step.
|
4. Pick up 2B, 9A, 2B, go with thread
up through the last 2 B beads, step #3, the last B bead and down through the
1st B bead, step #1, the first 2 B beads, step #3, and down through the first
2 B beads just added in this step.
|
5. Pick up 15B, go with thread up
through the last 2 B beads, step #4, the last 2 B beads, step #3, the last B
bead and down through the 1st B bead, step #1, the first 2 B beads, step #3, the
first 2 B beads, step #4, and the 1st B bead just added in this step. First
Unit complete.
|
6. Pick up 6B, go with thread down
through the 3 B beads as shown and up through the first 3 B beads just added
in this step.
|
7. Pick up 3B, 2A, 2B, 1C, 2B, go
with thread down through 2A and 6 B beads as shown in illustration, and up
through the first 3 B beads, step #6, and the first 3 B beads and 1st A bead
just added in this step.
|
8. Pick up 1A, 3B, go with thread
down through the 2 A beads, step #7.
|
9. Pick up 1B, 3A, go with thread up
through the 3rd A and 2 B beads, step #7, through the 3 B and 1 A bead, step
#8, down through the 1st A bead, step #7, and the 1st B bead just added in
this step.
|
10. Pick up 2B, 5A, go with thread up
through the 3 B beads, step #7, down through the B bead, step #9, and the 2 B
beads just added in this step.
|
11. Pick up 2B, 9A, go with thread up
through the 2nd and 3rd B beads, step #6, the 3 B beads, step #7, down through
the 1 B bead, step #9, 2 B beads, step #10, and the 2 B beads just added in
this step.
|
12. Pick up 14B, go with thread up
through the 6 B beads on the left side of Unit and down through the 6 B beads
on the right side of Unit as shown.
|
13. Continue necklace by repeating steps #6 through #12 until it fits.
14. To
add clasp, pick up 3A, clasp, 3A, go with thread up through 1B, 2A beads in
necklace. Continue with thread around through the clasp beads several times for
strength. Weave the working thread into the necklace and end. Repeat the clasp
directions in the same manner at the other end of necklace after removing the
stopper bead.
Scalloped Lace Necklace/Bracelet
Pattern, NB0151
http://www.SandraDHalpenny.com
Sandra D. Halpenny 2011 - 2019 All rights reserved.
This pattern may not be copied or distributed in any way without the express written permission of the author. The purchaser of this pattern may use the finished piece for personal use and for selling at arts and crafts shows, etc. No mass production of this design is permitted without permission from the author.
http://www.SandraDHalpenny.com
Sandra D. Halpenny 2011 - 2019 All rights reserved.
This pattern may not be copied or distributed in any way without the express written permission of the author. The purchaser of this pattern may use the finished piece for personal use and for selling at arts and crafts shows, etc. No mass production of this design is permitted without permission from the author.
